Required Tools for Assembly

Transformer & Wiring

Notes:

Screwdriver or power drill

Cable staples

How To Wire:

Transformer Size:

Creating Your Lighting Plan

Sample Lighting Plan

Here's one example of how to set up your outdoor lighting plan:

Under Deck Installation

Step 1: Plug your transformer into a standard 110-volt wall outlet. It will

transform the electricity down to the safe 12-volt level that your outdoor

lighting runs on.

Step 2: Plug the included remote control interface into the plug-and-play

end of your transformer (two-prong wire terminal).

Step 3: Plug a wire harness into the plug-and-play end of the remote

control interface (three-prong wire terminal).

Step 4: Use wire harnesses and splitters to connect all of your Effuse lights

to your lighting circuit. All Effuse Lighting products are compatible with

each other and use the same style of plug-and-play connectors.

Each light requires a certain wattage to power it. You'll need to make sure

your transformer has enough watts to power all of your lights.

Example based on diagram below:

Notes (Continued): You can run wiring inside of hollow metal posts or

composite post sleeves. For solid wood posts, you can drill channels for

the wires or run the wiring up the outside of your post and hide it behind

decorative trim(not included).

Wedge

Light

Outlet

Wire

Harness

2-Way

Splitter

Outlet

Transformer

Remote Control

Interface

Notes: Run wire harnesses under your deck frame, but don't run wires

between joists and deck boards. If you use cable staples to hold wires in

place, make sure the staples don't puncture or crush your wires.

Transformer

Connector

Wedge

Top Rail Installation

5/8" drill bit

1" drill bit

Your components may not look exactly like what's pictured in

diagrams, depending on your specific size and spec

Depending on your installation, you may need to enlarge the

center hole in your base plate using the supplied 5/8" drill bit

Centerpunch

Please Note:

Warranty Information

Low Voltage Installation Instructions & User Guide

Do not cut any wires. Only use Effuse Lighting products in your lighting plan.

It is the installer's responsibility to understand and adhere to local building

codes and safety requirements, and to obtain all required building permits

before installing. Effuse Lighting and your retailer are not liable for improper

or unsafe installations of this product.

Your Effuse Lighting is covered by a lifetime limited warranty! Installing

Effuse Lighting with wires, wire harnesses, transformers, or other appliances

outside of the Effuse Lighting brand will void all warranties.

Say Hello To Brighter Nights!

Congratulations on your new Effuse Lighting! We're so glad you chose to

work with us to brighten up your outdoor space. If you have any questions

or need further help with installation, please contact your retailer.

Share Photos So We Can Celebrate With You!

We would love to see pictures of your finished project and celebrate your

amazing new outdoor space with you! Tag #EffuseLighting on social

media to share your best photos. We especially love to see before & after

photos so we can celebrate the transformation!

Recomended tool

Electricians wire snake

Masking tape

Transformer (60W) 54W Max

Wedge Light 0.33 EA 160 Total

Lighting spread at different heights

Lighting shadows will appear based on the placement of the Wedge

light.

TOP

MIDWAY

LOW

Figure 1

5mm pilot drill bit

See Figure 2 for drilling information

Step 2: Remove Snap cover

Rectangular

Shaped

Rectangular

Loose

Post

Top Rail

Post

Snap Cover

Top Rail

Below Deck installation for Post To Post (P2P)

Step 1: Drill a 5/8" hole in base plate center and feed wire through

bottom up

Step 2: Measure and mark center of post, use a centerpunch and pilot

drill bit before drilling 1" hole for wire connector to pass through.

Figure 2

Pre Existing Railings

Step 3: Measure and mark center of post, use a centerpunch

and pilot drill bit before drilling 1" hole for wire connector to pass

through, Reference Figure 2

Post

Wire Harness

Top Rail

Post

Top Rail

Wire Harness

Rectangular Shaped

Note: Direct fascia mount situations using a wood crush block,

drill hole on backside of post above block for wiring

Above deck installation for Rectangular /Shaped Rail

Step 1: Loosen all cable tensioners using the appropriate tool.

5/8 Inch Dril Bit

Step 4: Feed wire harness through Posts and Top Rails

Shaped

1 Inch Step Drill

See figure 1

5/8 Inch Drill Bit

Direct Fascia Post

Fascia Bracket Post

Wire Harness

Wood Block

Wire Harness

Remote Control Setup

& Operation

The Effuse Lighting

remote control is

compatible with all

Effuse Lighting low

voltage and solar

lights. Approximate

range for operation

is 35 feet.

Turn Off Turn On

60-Second Delay OffCycle Colors

Select Color

Increase Brightness

Decrease Brightness

Timer

Cycle Through

5 Different Color

Temperatures

Turn Off Lights With

60-Second Delay

Quickly Select A

Color Temperature

Ranging From

Warm to Cool

Changing The Color Of Your Lights

Effuse Lighting is 5CCT - that means each fixture can emit light at

different color temperatures to better match the other lights inside and

outside of your home.

Cycle through the five color temperatures (2700K, 3000K, 3500K, 4000K

and 5000K) using your Remote Control.

WARNING:

1. The remote control included utilizes a 3V CR2025 battery: only replace with the same battery type.

2. Remove and immediately recycle or dispose of used batteries according to local regulations, and keep away from children. Do NOT dispose of batteries

in household trash or incinerate.

3. Even used batteries may cause severe injury or death.

4. The remote control contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. If you suspect your child has swallowed

or inserted a button battery, immediately seek urgent medical assistance.

5. Non-rechargeable batteries are not to be recharged.

6. Do not force discharge, recharge, disassemble, heat above 140°F / 60°C or incinerate. Doing so may result in injury due to venting, leakage or explosion

resulting in chemical burns.

7. Ensure the batteries are installed correctly according to polarity (+ and -).

8. Do not mix old and new batteries, di󰀨erent brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.

9. Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.

10. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries,

and keep them away from children.

INGESTION HAZARD: This product contains a button cell or a coin battery

DEATH or serious injury can occur if ingested

A swallowed button cell or coin battery can Internal Chemical Burns in as

little as 2 hours

KEEP new and used batteries OUT OF REACH of CHILDREN

Seek immediate medical attention if a battery is suspected to be

swallowed or inserted inside any part of the body.

WARNING:

Wedge lights

Step 1: Drill How To Install:

1-inch hole in post and run wire harness out

Step 2: Plug wire harness into the inside of wedge light

Detach the inside of the wedge

light from the outside housing. Plug it

in and test that your light turns on.

Wire

Harness

Wedge Light

Step 3: Use mounting screws to mount inside of wedge light to post or

post sleeve

Wedge light

Housing

screws

Mounting

Step 4: Slide wedge light housing onto inside of wedge light